One machine. One operator.
Art file in. Press-ready sheets out. The complete DTF production line (print, cut, powder, cure and stack) in a single footprint.
Engineered and built in Korea.
Sold and supported through authorized DTF Station dealers. Find yours for pricing, a live demo and installation.
The 3D model could not load on this device. The photograph stays.
Drag to turn · tap a dot to open it
Industrial printheads with a stainless-steel face, on two separated carriages. Two sets of media guides and a pair of film rollers hold the film flat the length of the bed, so head strikes are virtually impossible.
Learn moreColor Prime Chroma water-based pigment in sealed cartridges. White ink circulates every hour, the heads clean on a schedule, and after six hours idle they seal themselves into a wet cap, so a quiet week does not cost you a printhead.
Learn moreA single tilt touchscreen runs both sections. It tracks what maintenance is due and when it was last done, reports error codes back to support, and takes software updates on its own, so nothing depends on somebody remembering.
Learn moreOpen the doors and the whole finishing section is at hand: the powder cartridge on the left, the filter drawer on the right. Powdering, curing and filtration all happen inside the enclosure, at 67 dB(A) or less.
Learn moreAdhesive powder is metered from a sealed cartridge by a rotating paddle, and the excess is captured inside the machine. No loose powder, no tray to shovel. One cartridge runs about one full 100 m roll of film.
Learn moreA de-mist stage, a medium stage, then HEPA and activated carbon. Fumes and fine adhesive powder are captured inside the machine, so no external ventilation is required.
Learn moreAn enclosed conveyor bed with four independently controlled heater zones, held at 160 °C by a PID controller. The operator never sets a cure temperature, so there is no setting to get wrong and no result that depends on who is on shift.
Learn moreAn inline shuttle cutter trims each sheet in 0.8 seconds, at any length you choose between 25 and 50 cm. Finished sheets drop cut and squared into the integrated stacker, up to one hundred of them. Lift the stacker out and the run length becomes the roll instead.
Learn moreA 43.2 cm roll on a motorized, auto-tensioning unwinder with edge-driven pinch rollers. One 1.1 kg powder cartridge runs about one 100 m roll, so neither runs out before the other.
Learn moreThe print section mounts on top of the finishing section. Film feeds up and back down, so the wet ink side stays up while powdering and curing sit underneath the printer rather than beside it. Film goes in and comes out on the same side, so a second unit stands right next to the first.
Learn morePoint your phone’s camera at this code. The page opens on your phone; tap “See it in your space” and a full-size Vega S17 appears in the room, at true scale.
Every machine in this category is sold on the promise that you can send a job and walk away. Here is the mechanism behind each claim, so you can check it rather than take it.
Film travels a short, fully supported path and is cut into sheets rather than pulled on as one long web. There is no unsupported span for tension to act on, so there is nothing to skew, and nothing to stand and watch.
Fully enclosed, 67 dB(A) or less, with three-stage filtration that captures fumes and fine adhesive powder inside the machine. No external ventilation to install, so the building stops being the obstacle to bringing transfers in house.
Powder is sealed in a cartridge and applied automatically. The cure is preset. Cutting happens inline and finished sheets stack themselves, up to one hundred. Send the file and go run the press.
Adhesive powder is metered from a sealed cartridge by a rotating paddle, and the excess is captured inside the machine. No loose powder, no tray to shovel. One cartridge runs about one full 100 m roll of film.
An enclosed conveyor bed with four independently controlled heater zones, held at 160 °C by a PID controller. The operator never sets a cure temperature, so there is no setting to get wrong and no result that depends on who is on shift.
An inline shuttle cutter trims each sheet in 0.8 seconds, at any length you choose between 25 and 50 cm. Finished sheets drop cut and squared into the integrated stacker, up to one hundred of them. Lift the stacker out and the run length becomes the roll instead.
A de-mist stage, a medium stage, then HEPA and activated carbon. Fumes and fine adhesive powder are captured inside the machine, so no external ventilation is required.
A single tilt touchscreen runs both sections. It tracks what maintenance is due and when it was last done, reports error codes back to support, and takes software updates on its own, so nothing depends on somebody remembering.
The print section mounts on top of the finishing section. Film feeds up and back down, so the wet ink side stays up while powdering and curing sit underneath the printer rather than beside it. Film goes in and comes out on the same side, so a second unit stands right next to the first.
Specifications are subject to change. Confirm current specifications with your dealer before ordering.
Ask your local dealer for a live demo, current availability and the circuit requirements for your building before you decide.